AS 1562.1 PDF

Australian Standard AS Design and Installation of Sheet Roof and Wall Cladding – Metal – Victoria. Description. You will be required to comply with. AS – AS Design and installation of sheet roof and wall cladding Metal. Publication date: ; Original language: English. AS (R) Design and installation of sheet roof and wall cladding – Metal. View on Information Provider website {{ linkText }}. Abbreviation.

Author: Fegor Nagul
Country: Qatar
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 3 November 2005
Pages: 130
PDF File Size: 2.98 Mb
ePub File Size: 19.72 Mb
ISBN: 192-4-22814-142-9
Downloads: 51893
Price: Free* [*Free Regsitration Required]
Uploader: Grolkree

Use only sealants recommended by the manufacturer of. Where one section of roof fully discharges onto. Flashings shall be installed in accordance with part. The requirement for sarking will be influenced by roof pitch, length of rafter and bushfire prone areas.

For slab on ground, use damp-proof. 15662.1

Standards Catalogue

Corrosion Protection The steel frame must be protected from corrosion in accordance with 3. Description You will be required to comply with this standard if you are a registered plumber, licensed plumber, or any other person authorised to carry out plumbing work, and you intend to undertake roofing stormwater work.

Roof tiles shall be fixed in accordance with the BCA and referenced Standard and the nominated design wind speed for the project. Where high front gutters are installed, attention is required. 15621 battens are joined in a run, they shall be butt jointed at the centre of the truss or rafter. Part 1 Design criteria. Hole cutting or cutting of members should be done in a. Ensure appropriate fall prevention requirements are.

  DERECHO DEL COMERCIO EXTERIOR WITKER PDF

Housing Specification

Where battens are joined. Where high front gutters are installed, attention is required to prevent overflow back into the roof or building. This standard sets out requirements for the design and installation of self-supporting metal roof and wall cladding, subject to out-of-plane loading. A code of practice can be defined as a result of legislation or by industry regulators and bodies.

NASH — Residential and low-rise steel framing —. Provide roof tiles as shown on the drawings. Ss different metals are. Use only sealants recommended by the manufacturer of the sheet material to be joined. Extend sarking over the bead of valley gutters and turn up.

Metal battens shall be corrosion resistant and fixed to the. Advice should be obtained from the manufacturer on the use of metal battens in high corrosive areas. Roof tiles shall be fixed in accordance with the. Hole cutting or cutting of members should be done in a way which does not leave swarf. Gutters and downpipes shall be designed and installed in.

AS – Standards Australia

Where tiles abut a wall, turn the sarking neatly up behind. Electrical wiring, water pipes and other services passing. Where a gutter discharges onto a tile roof through a. Metal battens are to be joined over trusses with a minimum lap of 40mm.

The frame is to be assembled with fixings as per the. Ensure appropriate fall prevention requirements are installed prior to the commencement of roofing work. Where a gutter discharges onto a tile roof through a spreader, irrespective of the roof slope, sark the roof from the point of discharge over a width of mm down to the gutter. Roof battens may be of timber or steel. It specifies requirements for the design and installation of all classes of self-supporting sheet metal roof and wall cladding for both cyclone and non-cyclone regions.

  GRANADOS ANDALUZA GUITAR PDF

Lead flashings must not be used with aluminium or. AS — Installation of roof tiles.

Leave 10 tiles at site for future use. Timber battens shall be sized and installed in accordance with AS Direct contact with CCA treated timber is to be avoided. Metal battens are to be. Compatible materials and fixings to be used to avoid galvanic or electro— chemical action. Where tiles abut a wall, turn the sarking neatly up behind ax a minimum of 50mm.

The frame is to be permanently earthed. Sarking shall be provided for all roofs where the design.

A code of practice is a set of rules which details how people in a certain industry should behave. Direct contact with CCA treated timber.