ELIWELL ID970 PDF

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Kelkree Mausar
Country: Uzbekistan
Language: English (Spanish)
Genre: Marketing
Published (Last): 27 February 2015
Pages: 470
PDF File Size: 6.81 Mb
ePub File Size: 19.36 Mb
ISBN: 589-5-57251-220-1
Downloads: 22688
Price: Free* [*Free Regsitration Required]
Uploader: Tygorg

The indicated time must elapse between two subsequent switch-ons of the compressor. ID Single stage controller for temperature.

Eliwell ID970 MC (Milk)

Temperature alarm signal delay time. Defrost counting is always active when the machine is on and starts at each power-on. In addition, the 16 A compressor relay options id90 the buzzer are provided. This means, for example, that an error introduced by the probe is added to any error that is typical of the instrument.

Single stage controller for temperature – ID – Eliwell France

Users must not be able to access parts with dangerous voltage levels under normal operating conditions. The same applies to any person or company involved in preparing and writing this document.

Do not assemble the instrument in excessively humid or dirty locations since it is designed to be used in locations with normal pollution levels. The two sets are interdependent: The continuous improvement of our products can cause some variations in this non contractual document even without notice.

When enabled value other than 0it constitutes the access key for level 1 parameters. Defrost cycles can be controlled at time intervals.

  BEN HIGHMORE THE EVERYDAY LIFE READER PDF

Minimum possible setpoint value. Description Technical Schema Description: Alarm exclusion time after instrument is switched on following a power failure.

Every time the compressor stops, a defrosting cycle is id97 according to parameter dty dOH Defrost start delay time from start up of instrument.

In normal conditions, the labels for the Set point value is found in the menu. Probe cables, power supply cables and the TTL serial cable should be kept separate from power cables.

If one or more parameters jd970 modified, it is suggested to the switch off the controller after the modification and then switched back on. Erasing all parameters in the key. Compressor off time in the event of a faulty probe. It’s a community-based project which helps to repair anything.

It should be noted that the relay dliwell supplied with the device are functional and therefore exposed to potential faults.

Maximum possible setpoint value. The programming parameters are downloaded when the device is switched on.

Id790 parameter indicates that the protection is active on compressor relay actuations. HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe. Download from reset Connect the copy card when the instrument is OFF. Always make sure that the area next to the cooling openings of the tool is adequately ventilated.

Single stage controller for temperature. TTL for connection to Copy Card 3 outputs on relays: They are provided with a PTC thermostatic probe input NTC can be selected by parameter and two relay outputs for compressor and defrost management.

ID A Single stage controller for temperature. The instrument has screw terminals for connecting electrical cables with a maximum diameter of 2. Programming parameter transfer from instrument to Copy Card. Positive or negative temperature value added to the value read by probe Viewing mode during defrosting. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in an upward direction triggers the activation of the alarm signal.

  CHRISTOPHER MCQUARRIE WOLVERINE SCRIPT PDF

ID LX Single stage controller for temperature. Set point setting folder; -Pb1: Delay time in activating the outputs after switch-on of the instrument or after a power failure. The relay contacts are voltage-free.

The parameter indicates that a protection is active on the relay actuations of the generic compressor. Delay after switching off. For higher loads, use a suitable contactor. The password is enabled if the value of the PA1 parameter is not iv970.

Always switch off machine before working on electrical connections. For this page to function properly, you must enable JavaScript. View with decimal point. If you do eliwe,l enable JavaScript, certain features in this page will not function correctly.

Eliwell ID MC (Milk) |

Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets od970. Single stage controller for temperature ID The device must be suitably protected eliwdll water and dust according to the specific application and only be accessible using special tools except for the front keypad. Although Eliwell has taken all possible measures to guarantee the accuracy of this document, it declines any responsibility for any damage arising out of its use.

JavaScript is disabled in your browser.